Bowling Pin Dimensions and Layout of the Bowling Pin Rack

Bowling Pin used in tenpin, five-pin, candle-pin, and duck-pin bowling plays a fundamental role in the game of bowling. The bowler targets it with bowling balls. As far as the cost of the bowling pin is concerned, a set of ten pins costs about 150 USD to 160 USD.

Dimensions and Layout of the Bowling Pin Rack

There are different bowling pin specifications according to their size, shape, weight, length, and the game.

United States Bowling Congress (USBC) sets the standard of the bowling pin adopted by World Bowling formerly known as the World Tenpin Bowling Association. The weight of the pin is usually based on about twenty-four percent of the ball.

Bowling pins are made of hard maple wood and are either plastic coated or constructed in one piece or laminated in two or more parts.

The weight of a standard wood pin or a plastic-coated pin is not less than three lbs., 6 ounces and not more than three lbs., 10 ounces.

The diameter of the cup at the base of the pin is 3/4″.

The base width of a pin is 2 1/4″. The narrowest pin diameter is 1.8″ and about 10″ above the base of the nail and is sometimes referred to as the “neck” of the pin.

The Center of Gravity of a pin, measured from the bottom of the nail, is 5 5/16″ or about one-third way up the height of the pin and approximately one inch above the most extensive pin diameter area of 4.76″ measured 4.5″ above the pin base.

The Center of Gravity of a bowling pin and the fullest part of the pin diameter are both very near the same point where a bowling ball contacts the pin given that the range size of a bowling ball is also about 4.5 inches above the lane outside.

The center of the seven and the ten pin spots are located 2.75″ from the edge of the lane. The pin spots are 2 1/4″ in diameter and must be spaced 12″ apart in an equilateral triangle formation.

With the advancement in the game of bowling, the construction process of the pin hasn’t changed in over 60 years! Back in the late 1800s. At that time, manufacturers produced bowling pins with solid pieces of maple.

But with the invention of the pinsetter in the 1940s, the bowling pin was easily damaged and needed to be often replaced.

Vulcan Manufacturing invented a solution in the 1950s and started to use pieces of maple wood and gluing them together.

This method allowed for a bar’s weight to be controlled, while at the same time creating strength to withstand the impact of bowling balls and being tossed around in a pinsetter.

As a result, the bowling pin in the modern form was born, and, by the early ’60s, the usage of solid bowling pin wood had stopped.

As per the regulations, it is the need to grow the maple trees above the 45th parallel (running through the northern part of the United States).

Bowling is a sport widely played in developed countries like the USA, UK, Canada, Australia, and the rest of western Europe. Bowling bar is an integral part of this game.

Bowling Pin Wood And Other Material Used

Bowling pin created with rock maple wood, coated with the plastic material, and painted. Due to the scarcity of appropriate bowling pin wood, approved synthetics came into use.

Bowling Pin created with synthetics, the bowling material, are mostly used in five-pin, duck-pin, and candle-pin bowling games.

United States Bowling Congress (USBC) has approved one synthetic tenpin bowling pin model. Sounds of the plastic bar and wooden bar are different from each other when hit by the bowling ball.

If you were to ask a wide range of people of varying demographics from which material bowling pin made, you would likely be surprised at their answers. Wood? Metal? Plastic? Aluminum?

There is a need to preserve the maple wood. Nylon and Surlyn save the forest and give its white appearance.

The coating processes used on the pins depend upon which coating is being applied. For instance, with nylon coatings, the bowling pin must first be sealed in latex to ensure the nylon adheres correctly and to prevent it from cracking.

Once the coating is applied, the surface is first sanded to remove the excess coating, and then sprayed onto the bar silkscreen graphics. These look like the ring around the neck and the manufacturer’s logo.

Finally, he has to spray a clear gloss coat over the bar, then glues bar skirt onto the bottom of the bar. The bowling Pins will last around a year on average, but a recoat is needed after about six months.

The bowling pin, created with the material that will be easier to build, is an essential part of a bowling scene.

The material used in the construction of the bowling pin comprises three parts. These are the stripes, glossy, and dirt part.

Stripes are made using sinus curves which will cause it to oscillate between 1 and -1. By using a restriction on the minimum value, it will swing between 1 and 0. Furthermore, around nodes will beget a figure of 1 and 0 thereby changing the colors. Glossy is made with a light shader and a mixer.

Dirt: The dirt is the last part, as it should not be affected by the glossy. It is made with a noise texture and controlled by a power node.

Dimensions – Width/Length

Dimensions of bowling pins are different depending upon tenpin, duck-pin, five-pin, and candlepin. The length of Tenpin bowling pins is 4.75 (width) x 15 (length) inches, and their weight is 1.5 KG to 1.6 KG. Bowling pin size varies considerably.

Duckpins are a little bit smaller and squatter the standard bowling pins. Canadian five-pins are between tenpin and duckpin, but they contain rubber bands around their widest part.

Candlepins are tallest of all of the above. They are 15-3/4 inches tall and 2-16/16 inches wide. Their weight is 1.1 KG each. They are cylindrical and look like candles. 5 pin bowling pins also have different sizes.

Everyone should learn about bowling pin specifications. Knowledge is always vital in the way of improvement. We have to examine useful bits of information about the United States Bowling Congress (USBC) bowling pin specifications.

First, bowling pins are made of hard maple wood and are either plastic coated or constructed in one piece or laminated in two or more parts.

Bowling pins deteriorate with the passage of time and with the collisions of the balls. USBC specifies maintenance procedures to preserve the life and usefulness of the pins.

The use of steel wool or sandpaper to remove dirt and surface splinters and the application of finish and their patching is allowed.

Bowling pin specifications must be kept in mind. They are easier to understand how a bowling ball is broad enough to contact both adjacent pins in the same row of the bowling pins.

A bowling ball has the proclivity to deflect as it contacts the right edge of the three-pin to also reach the left tip of the tenpin for the right-handed bowler.

As the bowling ball hooks too sharply just before impact with the three-pin, then it will not contact the ten bar as well. That is why most top-flight amateur and professional bowlers will use across angle delivery. The purpose behind this tactic to avert hooking fo the ball too severely.

Most Related Articles:

Leave a Comment